These Jeti Anti Spark Connectors are designed for connections between the battery and electric speed controller. They are equipped with a circuitry for limiting the charging current to the capacitor controller and thus prevent an electric shock during connection. By eliminating electrical discharge, it significantly increases the life of the connectors and the reliability of connection. 

The Jeti Model MGPS sensor defines the exact model position and calculates speed, altitude and distance from the point of origin. In addition, the course, azimuth and the total covered distance can also be recorded.

These Jeti Anti Spark Connectors are designed for connections between the battery and electric speed controller. They are equipped with a circuitry for limiting the charging current to the capacitor controller and thus prevent an electric shock during connection. By eliminating electrical discharge, it significantly increases the life of the connectors and the reliability of connection. 

The Jeti Model DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2.4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bi-directional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. 

The JetiBox Profi is a mobile wireless device, offering maximum comfort to the user when viewing, processing and storing telemetric data. An integral part of the JetiBox Profi is the system Jeti Duplex 2.4GHz, which can be alternatively operated in one of the two offered wireless modes. 

The Jeti Duplex R8 2.4GHz Receiver is a dedicated receiver to receives signals to and fro your radio transmitter via the use of Duplex 2.4GHz Transmitter Module.

Jeti Model SPIN is a top end series of speedcontrollers for brushless motors. Due to their numerous adjustment possibilities, SPIN controllers are the preferred choice for all airborne applications including helicopters and belong to the usual equipment of top pilots. SPIN speedcontrollers record operating data during operation, which allows you to examine the data and fine tune the settings of your airplane or helicopter. A large heatsink at the back of this speedcontroller helps dissipate heat at higher power levels.

Programming of the SPIN speedcontroller can be done via the JETIBOX. The Spin 125 features an anti-spark wire. When connecting the controller to your flight battery pack, first connect the negative/black wires, followed by the small red anti-spark wire and finally the positive/red wires. The package is complete with three pairs of 4mm gold connectors and heatshrink. 

Jeti Duplex 2.4GHz TF Module (Futaba) is assigned to transmitters with exchangeable HF plug-in modules. TF modules are compatible to corresponding exchangeable modules of Futaba and Hitec transmitters.

The Jeti Model Maz BEC 2D is a linear voltage regulator, to provide power for the receiver and servos used in your models. For increased safety and reliability of this device, a magnetic switch is used to switch the unit on and off. The Jeti Model BEC 2D is fully compatible with the Jeti Duplex System and can also be operated using the Jeti Box terminal.

The Jeti Model MRPM-AC is used exclusively for measuring the speed of brushless DC motors on your models in flight. The current speeds and the historical course of the propeller performance (minimum & maximum) are monitored.

The Jeti Model switching Voltage Regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells.

The Jeti Expander E4 is use to expand the number of connecting places for further telemetric sensors, expanding up to 4 telemetric sensors connections to the Jeti Duplex 2.4GHz Receiver.

The Jeti Model Duplex MUI 50 sensor measures your battery pack's voltage/current data and transmits them real time with the aid of the Jeti 2.4GHz DUPLEX System (receivers & transmitter modules). It can also at the same time report the actual capacity used in mAh. The Duplex MUI 50 measures current up to 50A and current up to 60V.  When connected together with the Jeti Box, it works great as an ammeter or a voltage meter.

Jeti Muli 6s (LiPo Monitor) is sensor for checking voltage of Li-XX batteries that checks the voltage by service connector of each cell. It allows you to check the voltage up to 6 Li-XX cells. You can check voltage of each cell, store its history (maximum & minimum), total voltage of battery pack and the sensor also can give notice of exceeding selected parameters. Data from the sensor can be sent wirelessly via the Jeti DUPLEX system.

The Jeti MU3 sensor (3 Voltage Monitor) can be used for model on board monitoring of up to three voltages. With the aid of the MU-3 sensor the voltage can be monitored (minimum and maximum values) and the sensor may warn the user if set parameters are violated. Informations of the sensor are transmitted by the Duplex System to the user.

The Jeti Model Duplex MUI 200 sensor measures your battery pack's voltage/current data and transmits them real time with the aid of the Jeti DUPLEX system. It can also at the same time report the actual capacity used in mAh. The Duplex MUI 200 measures current up to 200A and current up to 60V.

The Jeti Model USB Adapter is used to transfer information between computers and Jeti model devices with the USB Support.

The Jeti Voice-1 Assembly Kit consist of accessories (an external siren and headphone jack) allowing audio output from the TU2 module.

The Jeti Duplex R6 2.4GHz Receiver is a dedicated receiver to receives signals to and fro your radio transmitter via the use of Duplex 2.4GHz Transmitter Module.

Jeti Model Duplex TU2 Module is suitable for all transmitters. It is possible to install it into all transmitters with two main requirements: Transmitter that can operate in the PPM mode and available space for the module in transmitter.

Jeti Model MSpeed (Airspeed Monitor) is a sensor which measures the speed of a flying model through the air, to provide the indicated airspeed (IAS). The reporting of airspeed can be very instructive with regard to the control of a flying model, for example allowing the pilot to determine the models stall speed and set an alarm to indicate when the model falls below this speed.

The Jeti Model Duplex MUI 30 sensor measures your battery pack's voltage/current data and transmits them real time with the aid of the Jeti 2.4GHz DUPLEX System (receivers & transmitter modules). It can also at the same time report the actual capacity used in mAh. The Duplex MUI 30 measures current up to 30A and current up to 60V.  When connected together with the Jeti Box, it works great as an ammeter or a voltage meter.

The Jeti Model MT 125 Sensor measures temperature of your model's devices like motors, controllers, batteries and other accessories. These recorded data can be delivered real time to the JETIBOX when connected using the Jeti DUPLEX 2.4GHz system.

The Jeti Model MT 300 measures temperature of devices on your model like motors, speed controllers, batteries and other accessories. The measured data is presented on the JETIBOX terminal via wireless transfer with the aid of the Jeti DUPLEX 2.4GHz system. 

The Jeti Duplex MRPM sensor provides RPM and power measurements for propeller driven models. Included with the unit is an optical sensor which performs measurements by monitoring the interruption of light through the rotating propeller, per minute. The MRPM sensor measures the propellers current speed and performance of the propeller and provides warnings when preset parameters are exceeded.

The Jeti Model MVario System measures the atmospherical pressure and calculates with the obtained data the altitude above sea level, the rate of climb as well as the rate of descent and records extreme values of these data.